Search results

One note on the retrofit of a Maxxair fan. The interior trim bezel from the Fantastic fan will work with the Maxxair and it makes it easier to cover visible screw holes that have to be dealt with if the Maxxair bezel is used. It is easier and cleaner to just reuse the original Fantastic trim...

Adjusting the camber on a trailer axle requires a special fixture like we have here at the factory. Basically have to bend the axle a little bit with some hydraulics. Cary

Frank and Franci, A Forester has a 1500lb tow capacity so will tow any of the 550 series models we offer. Very common tow vehicle we see being used for this model. It would be a bit too light a tow capacity to pull a 560 series. 550 models have been built 24 years so a older used one may be a...

Crowning the axle is a description of doing a camber adjustment on the axle to make sure the wheel camber is perfectly correct. As the camper gets miles the axle tends to wear in and the camber changes a bit. Older models left with not enough camber also so older models benefit the most. A newer...

We have a new Road Toad listed on Ebay right now. It is a scratch and dent with some minor dents in the side wall. Here is the listing: 2024 Road Toad Teardrop Camper Travel Trailer, Light Weight Under 500 lbs. | eBay

Got to hang out with Tour931 for a bit today. It was good catching up with him. Cary

I have seen one customer recently install a latex foam mattress. It is super soft and was his solution. It is a bit heavy and a hassle to wrestle around and such but oooh is it comfy. He used it on top of another firmer mattress. The Latex does not provide adequate support to use on it's own so...

I just got off the phone with Fred and this camper did sell. Congrats to Jimg! Welcome to our little community, Cary

Congrats Kevin! Cary

Randy, For sure your camper battery is not being fully charged while driving without a DC to DC charger. If the camper has just a base straight charge line from the tow vehicle we estimate about 80-85% maximum charge on the camper battery. Having a DC to DC charge like the CTEK , Victron or...

Hmmm, Green Spot. Oh ya. Cary

Sweeney, Did you drop down your electronics tray? To do that, take out the battery. Then the wooden panel with the fuse panel, volt meter and DC switch has two screws that hold it in place. Take those to screws out and pull the face out and down. That will drop down the tray to access all...

Sweeney. You know we lay awake at night trying to figure out how to use that extra 1" of space. That is the mission for sure. I knew you would have to have a battery monitor with more data points. Ha! This made my day. Cary

Camp-Inn has a new email address! We are updating and improving our internet and email system and in the process have changed to a new email address. The new email address is sales@tinycamper.com Emails sent to our old email address will be forwarded to the new email address so we will...

I figured someone would want details on this. For the most part the complaints of devices not working with our hoses were very random. Typically BBQ grills and camp stoves. Random but very often. The hose would work for the customer on one appliance and then no gas flow on a different appliance...

Ya, not the same. The Coleman one is just a hole with what looks like a bronze screen in it. That is more the normal fitting. The MH fitting actually has a valve that needs to be pushed in on to open up to let gas flow into it. This completely explains it then. Sweeney did mention his hose has a...

Aha!!! This solves it. Mr Heater has a one way valve of some sort on the fitting. Never seen anything like this before. That explains why the Camp-Inn provided hose is not working then. Because we pull the Schrader valve out of the hoses to make sure they will work with a broad range of gas...

So, here is a question for those who have a Buddy heater. Does the 1lb propane connection fitting have some sort of Schrader valve in it? Are they somehow having two Schrader valves push against each other? Normally a gas appliance has a pin with a small hole in the end that pushes on the...

Does someone make a bleed valve for a 1lb bottle fitting? Cary